Valeo J02-00
- 9651197480A
- 9651196780A
Peugeot · Citroen · BSI · ECU · replacement modules
Peugeot Citroen BSI & ECU Programming
Peugeot and Citroën BSI cloning, replacement BSI programming and engine ECU cloning in Stourbridge, Birmingham and the West Midlands, with UK postal service for compatible modules.
✓ Vehicle-specific checks✓ Controlled programming✓ Clear verification
BSI cloningECU programmingBody-system codingReplacement modules
Peugeot & Citroen electronics
Peugeot BSI cloning and Citroën ECU programming.
The BSI can be involved with locking, lighting, wipers, immobiliser functions and other body electronics. A replacement unit may therefore need data transfer and vehicle-specific configuration.
We check the original and donor part numbers, communication state and vehicle symptoms before selecting the repair route.
Before we program anything
✓Vehicle and module identification checked
✓Diagnostic fault information reviewed
✓Compatibility confirmed where possible
✓Programming route selected for the exact job
Workshop & bench work
BSI programming linked to real body-electronics diagnosis.
A replacement BSI should not be programmed until the original fault, donor compatibility and vehicle-side wiring have been considered.
BSI / body module
Body-control module identification and replacement programming are matched to the exact vehicle.
Electrical checks
Power supply, wiring and connector faults are checked before BSI programming.
Steering electronics
Body and steering electronics can require coding or calibration after replacement.
Coding verification
Full-system communication and stored faults are checked after programming.Peugeot & Citroën BSI and ECU part numbers.
Use these catalogue examples to compare the references on your module label. Send clear photos of the original and replacement units, together with the VIN and fault codes, before booking BSI cloning or ECU programming.
BSI body-control module references
Valeo M4 / PR4 V6.2
- 9642409880
- 73006212
- A11975
Siemens B4 / D9
- 9640091380
- S110950410C
Johnson Controls BSI04EV K04-00
- 966405908002
Engine ECU references
Bosch EDC17C10
- 0281017333
- 9677013180
Bosch EDC17C10-5.11
- 0281019817
- 9805947380
Bosch EDC17C60
- 0281031886
- 9813283780
Bosch EDC17C60
- 0281033849
- 9822917680
These examples identify module families and label numbers. Available cloning, coding and programming functions are checked against the exact hardware, software and original data. Include every suffix printed on the module label when requesting a quotation.
Service options
Peugeot & Citroen programming services.
Support depends on BSI generation, ECU family and available original data.
BSI cloning & data transfer
Supported transfer of vehicle-specific data to a compatible donor BSI.
Engine ECU programming
Replacement ECU programming and cloning where supported.
Body-system coding
Configuration of supported options after BSI replacement.
Immobiliser-related setup
Security data considered where the BSI and ECU are linked.
Typical enquiries
Common Peugeot & Citroen enquiries.
These cases often involve multiple body functions or a previously fitted donor BSI.
Wipers or body functions fail
BSI, wiring and configuration need diagnosis.
Used BSI fitted
Replacement module requires supported data transfer or coding.
No-start after module replacement
BSI/ECU immobiliser relationship needs assessment.
Water or corrosion damage
Original BSI may be unreliable and require donor replacement.
Specialist support
Original and donor modules need to be matched carefully.
Part number alone is not always enough. Hardware, software and stored vehicle data can all affect whether a donor is suitable.
Module-label comparison
Original and donor references checked before programming.
Vehicle wiring checks
Power and body-system faults considered before condemning the BSI.
Bench data handling
Supported EEPROM/flash data handled according to controller type.
Function verification
Affected body systems checked after programming and refitting.
Identify. Diagnose. Program. Verify.
Identify original BSI
VIN, label, fault codes and symptoms recorded.
Check donor
Replacement hardware and software compatibility assessed.
Clone / program
Supported data transfer or configuration completed.
Refit & verify
Communication and affected body functions checked.
Body-control faults can be caused by wiring, water ingress or external loads. Programming a donor BSI will not repair those underlying vehicle faults.
Peugeot & Citroën BSI cloning in Birmingham and across the UK.
SG-Tronic Motorsport provides Peugeot BSI cloning, Citroën BSI replacement programming and compatible engine ECU cloning from our Stourbridge workshop near Birmingham. We assess no-start faults after module replacement, lost body-system coding and donor-module matching before selecting the programming route.
Workshop enquiries are welcome from Dudley, Wolverhampton and the wider West Midlands. Selected mobile diagnostics and coding can be arranged where the job is suitable; bench data transfer requires the removed module. Approved units can be sent by tracked post from across the UK, including Scotland, Wales and Northern Ireland. Postal enquiries from Ireland and international customers are assessed before shipping.
Read about our BSI cloning and replacement-module programming, or review the ECU cloning service for engine-controller replacement. Our postal module service explains how to arrange an approved bench job.
BSI cloning and ECU programming questions.
Can you clone a Peugeot or Citroën BSI?
Selected BSI modules can be cloned or programmed when the original data can be read and the replacement unit is compatible. Send the VIN, both module labels and the fault codes before booking.
Can you program a used replacement ECU?
Supported used engine ECUs can be assessed for cloning, coding or adaptation. The original ECU data, donor hardware and software version determine which route is available.
Where can I find my BSI or ECU part number?
Photograph the complete module label, including the manufacturer reference, vehicle part number, hardware/software identifiers and any suffixes. The example numbers on this page help identify the label references; matching a number alone does not confirm compatibility.
Does BSI programming fix wipers, locking or no-start faults?
These symptoms can involve BSI configuration, wiring, power supply or another controller. Diagnostics are used to identify the cause before replacement programming or data transfer is recommended.
Do you offer BSI programming in Birmingham or by post?
Workshop service is available in Stourbridge near Birmingham. Selected mobile diagnostics and coding are available in the West Midlands where suitable. Approved removable modules can be sent by tracked post from across the UK, with Ireland and international enquiries checked before shipping.
What should I send before requesting a quotation?
Send the VIN or registration, make/model/year, engine code, diagnostic fault codes, symptoms and clear original/donor module-label photos. Include details of previous repairs or programming attempts.
Need a compatibility check?